MSP430 Emulator MSP-FET430UIF Automatic Upgrades USB Debug Interface Programmer

Description

Description
MSP430 USB Debug Interface Emulator MSP-FET430UIF Support JTAG BSL SBW
Advantages:
1, Original program circuit, performance 100% compatible with the original;
2, Support the full range of MSP430 MCU electrode sheet;
3, The device is imported;
4, Support the working voltage: 1.8V ~ 3.6V
5, Can automatically update the firmware
6, With full SMT processing, quality assurance, gold craft;
7, Support for multiple compilers (eg: AQ430, IAR, CCS, etc);
8, Support for JTAG, SBW, BSL;
9, Support has been programmed to read and blown fuses
10, Support XP, VISTA, win7, win8, and other operating systems;
11, Support FET-PRO430 software, supports batch mode programming chip JTAG port.The technology is available.
Note:
1. JTAG emulator second leg is the power output pin, if the first two legs and the target board is connected, that is internal power supply, when the target board does not require programming simulation power, 4 feet to be suspended;
2. JTAG emulator of 4 feet is the power input pin, 4 feet and if the target board is connected, said the external power supply, when programming emulator target board requires power, and the second leg to be vacant;
3. Make sure the emulator connection line is a load, if applicable, disconnect, or they may fail simulation;
4. If you are using the simulation process, due to improper operation or stopped suddenly dropped and so did the program compile and debug environment unplug emulator, then connect again when debugging emulator, there may appear to connect the communication fails, should unplug the USB cable, re-drive IAR compiler environment, plug in again emulator like.
That leads to the programmer as a BSL figure when DTR, RTS, RXD, TXSD interface, suitable for mass production when the target chip programming, this emulator is the rest of TI pin standard JTAG interface for a full range of MSP430 chip emulator and download.
MPS430 either emulator or programming process, generally by: JTAG, SBW, BSL were imported.
1, JTAG boundary scan technology is the use, in the internal logic 430 to the JTAG port to use, has a number of internal registers connected to the address on the internal data bus 430, it is possible to access to all resources 430, including full address FLASH, RAM and various types of registers. 430 also can be used to need another two lines RST, TEST to start JTAG command sequence.
2, SBW is SPY-BI-WIRE, can be referred to as two-wire JTAG, mainly SBWTCK (connected to the JTAG interface is 7 feet TCK) and SBWTDIO (connected to a pin JTAG connector TDO / TDI), the interface is mainly used less than 28 feet in two series of microcontrollers, because JTAG 28 feet within the microcontroller and IO port multiplexing general, in order to leave more for IO resources, was launched SBW interface. Like SBW 430 JTAG access to all resources inside.
Note: Currently MSP430F5XX series also has SBW interface principles with two series of SBW.
3, BSL is TI at the 430 factory pre-fixed to the MCU internal section of code that the user can not read and write, which is somewhat similar to the DSP's bootloader, but there is a clear distinction with bootloader, BSL can only be used for internal MCU the FLSH access, not access to other resources, it can only be used as the programming interface. BSL via UART protocol with the programmer child New Year. The programmer can send different commands MCU communication device savings have to do different operations, you can put it that way for BSL interface.
Emulator and connection between the target board MSP430 MCU series is divided into two wire connections and 4-wire connection, as shown in Figure :( Note two: JTAG interface definition description can be obtained from the following figure)
Package included:
- 1 x MSP430 USB emulator
- 1 x USB Cable
- 1 x JTAG Cable
- 1 x DVD
Shipping Terms
- For remote regions, we will charge your extra shipping costs. Usually it cost about 35USD-50USD. We will contact you after your payment. Thanks for your understanding.
Custom Duties & Taxes
1. Import duties, taxes, and charges are not included in the item price or postage cost. These charges are the buyer's responsibility.
2. Avoiding some unnecessary trouble, please check with your country's customs office to inform us what we should declare its value before shipping.